GMC

Ididit's 1955-68 Horn Kit has everything you need to adapt most 55-68 GM stock steering wheels to your Ididit steering column. Comes complete with aluminum trim ring, horn contact plate, spring, pin, and retainer.

On this kit we used a traditional style rear steer rack & pinion that is mounted to a one piece bracket which bolts up to the outside of either frame rail in the same holes as the original steering box and idler arms.

This kit is for rear wheel drive vehicles only, NOT 4x4s. Installs have been done on V-8s, so there should be room if using a 6 Cylinder. There is quite a bit of room for the shaft support, but some headers may require modification. A two groove pulley on your water pump is required for this kit.

Note: If using drum brake spindles order kit 8011740-01.

On this kit we used a traditional style rear steer rack & pinion that is mounted to a one piece bracket which bolts up to the outside of either frame rail in the same holes as the original steering box and idler arms.

This kit is for rear wheel drive vehicles only, NOT 4x4s. Installs have been done on V-8s, so there should be room if using a 6 Cylinder. There is quite a bit of room for the shaft support, but some headers may require modification. A two groove pulley on your water pump is required for this kit.

Note: If using disk brake spindles order kit 8011920-01.

This wiring kit is used to adapt your Full Size Chevy and Chevy Truck stock wiring to your ididit column, while adding the safety of a 4-way flasher to your vehicle.

On this kit we used a traditional style rear steer rack & pinion that is mounted to a one piece bracket which bolts up to the outside of either frame rail in the same holes as the original steering box and idler arms.

This kit is for rear wheel drive vehicles only, NOT 4x4s. Installs have been done on V-8s, so there should be room if using a 6 Cylinder. There is quite a bit of room for the shaft support, but some headers may require modification. A two groove pulley on your water pump is required for this kit.

Note: If using disk brake spindles order kit 8011650-01.

On this kit we used a traditional style rear steer rack & pinion that is mounted to a one piece bracket which bolts up to the outside of either frame rail in the same holes as the original steering box and idler arms.

This kit is for rear wheel drive vehicles only, NOT 4x4s. Installs have been done on V-8s, so there should be room if using a 6 Cylinder. There is quite a bit of room for the shaft support, but some headers may require modification. A two groove pulley on your water pump is required for this kit.

Note: If using drum brake spindles order kit 8011900-01.

On this kit we used a traditional style rear steer rack & pinion that is mounted to a one piece bracket which bolts up to the outside of either frame rail in the same holes as the original steering box and idler arms.

This kit is for rear wheel drive vehicles only, NOT 4x4s. Installs have been done on V-8s, so there should be room if using a 6 Cylinder. There is quite a bit of room for the shaft support, but some headers may require modification. A two groove pulley on your water pump is required for this kit.

This kit includes an UNPOLISHED C-5 TC low flow pump, and TC reservoir for a long water pump Big Block engine.

This kit includes an UNPOLISHED C-5 TC low flow pump and TC resevoir for a short water pump Big Block engine.

This bracket kit is designed to be used with our GM Type II/TC power steering pump.

This kit includes a POLISHED C-5 TC pump with OE fitting low, and remote reservoir for a long water pump Big Block engine.

This kit includes a POLISHED C-5 pump with OE fitting low, and a remote resevoir for a short water pump Big Block engine.

This power steering pump kit is designed to compliment our Chevy Rack-Only kits. This kit includes a POLISHED pump and POLISHED remote resevoir for a short water pump Small Block engine. The pump is a high flow pump running at about 1500 psi and 3 gpm.

This kit includes an UNPOLISHED C-5 TC low flow pump, and TC resevoir for a short water pump Small Block engine. High Mount on Motor.

Low Mount pump.

Includes:

• Unpolished C-5 TC low flow pump
• TC resevoir for a short water pump Small Block engine.

This kit includes a POLISHED C-5 pump with OE fitting low, and remote resevoir for a long water pump Small Block engine.

This retrofit column is designed to fit your C10. This Chevy Style column features all Chevy wiring and a C10 top shaft. It will bolt to your stock box or rack & pinion system. Simply remove your old column, saving your original under-dash mount. This item has a collapsible inner shaft. Using this installation kit you will be able to install your new steering column in place of the old.

Includes:

• 8-Position Tilt
• Ford Turn Signal Switch
• Ford Style Knobs and Levers
• Ford Top Shaft
• 3/4" 36 Lower Shaft

ididit steering column drops and underdash mounts are designed for a variety of applications. They're machined from Billet Aluminum, and this lustrous design is available in Brushed or Polished finishes.

Made in America

ididit steering column drops and underdash mounts are designed for a variety of applications. They're machined from Billet Aluminum, and this lustrous design is available in Brushed or Polished finishes.

Made in America

ididit steering column drops and underdash mounts are designed for a variety of applications. They're machined from Billet Aluminum, and this lustrous design is available in Brushed or Polished finishes.

Made in America

ididit steering column drops and underdash mounts are designed for a variety of applications. They're machined from Billet Aluminum, and this lustrous design is available in Brushed or Polished finishes.

Made in America