138 products

1965-66 Mustang Power Rack & Pinion for Small Block
Product# 8010890-01-01
Regular price $1,850.00 Save $-1,850.00Our early Mustang Rack Kit greatly improves the steering and handling when compared to that old steering box. This is a center take-off style rack and pinion that utilizes an offset ball center bar which duplicates the stock center link; this means that the rack matches the exact geometry of the original front suspension. Effectively eliminating bump steer, and creating great handling.
The rack comes mounted to a one piece mounting bracket which replaces the tubular cross member located directly behind the front suspension. Since the racks are center take-off style, we off set the rack on the mounting bracket; moving the pinions closer to the driver-side frame which makes connection of the steering linkage to a column as easy as possible.
From a steering standpoint, we found that the early Mustangs split mid 1967 and there were slight differences, so make sure you order the correct kit! Additionally, later model Mustangs and Cougars may look the same, but are NOT - check out our Cougar Rack & Pinion Kits.
The kit will work on Small Block cars, and have been successfully used with Stock Manifolds, and Hooker Super Comp Headers. Tri-Y Headers have worked with 289, and 302 engines. Other Headers may work, but we can't guarantee an easy install. This kit requires the use of a mini starter. This kit may require some modifications on Mustangs with Dart Heads and other Aftermarket Heads requiring different headers.
Note: Granada Spindles have been used on these cars. Please indicate this to us with the drop down menu above, so we can swap the outer ends you will need.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN | Pump & Line Kit |
Return Port Size: | 16mm - 6AN | Steering Shaft Kit |
Pump Required: | Low Flow 1100 psi | Mounting Hardware |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | 8021120 / 8021300 | |
Granada Outer Ends | 8021250 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1982-95 Chevy S10/ Sonoma Rack & Pinion kit, Black
Product# 8000990-01
Regular price $1,300.00 Save $-1,300.00On this kit we used our own build of manual rack and pinion in a center take-off style rear steer rack. This style of rack and pinion bolts up into place where the existing steering box and idler arm is bolted. This unit is pounds lighter than the original steering and maximizes clearance for V-8 swaps. On a V-8 swap, we successfully used Hedman Shorty style headers. This kit has been used on project cars that use an S-10 frame, but the linkage back up to the column is up to you. This kit is for 2-wheel, rear wheel drive vehicles only.
Note: You will need to reuse or obtain the two factory 5/8"-18 right hand thread outer tie rod ends for this kit.
Tech Info: |
Kit Includes: | |
Pinion Type / Size: | 9/16" - 26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Mounting Bracket |
Turns Lock to Lock: | 4.5 Turns | Steering Shaft Kit |
Pressure Port Size: | NA | Mounting Hardware |
Return Port Size: | NA | |
Pump Required: | NA | |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | Reuse Originals | > |
Click Here to Look at Product Instructions

Late 1967-70 Power Mustang Rack & Pinion for Small Blocks
Product# 8010830-01-01
Regular price $1,700.00 Save $-1,700.00Our early Mustang Rack Kit greatly improves the steering and handling when compared to that old steering box. This is a center take-off style rack and pinion that utilizes an offset ball center bar which duplicates the stock center link; this means that the rack matches the exact geometry of the original front suspension. Effectively eliminating bump steer, and creating great handling.
The rack comes mounted to a one piece mounting bracket which replaces the tubular cross member located directly behind the front suspension. Since the racks are center take-off style, we off set the rack on the mounting bracket; moving the pinions closer to the driver-side frame which makes connection of the steering linkage to a column as easy as possible.
From a steering standpoint, we found that the early Mustangs split mid 1967 and there were slight differences, so make sure you order the correct kit! Additionally, later model Mustangs and Cougars may look the same, but are NOT - check out our Cougar Rack & Pinion Kits.
The kit will work on Small Block cars, and have been successfully used with Stock Manifolds, and Hooker Super Comp Headers. Other Headers may work, but we can't guarantee an easy install. This kit requires the use of a mini starter. This kit may require some modifications on Mustangs with Dart Heads and other Aftermarket Heads requiring different headers.
Note: Granada Spindles have been used on these cars. Please indicate this to us with the drop down menu above, so we can swap the outer ends you will need. Also, If you have a 351C motor you will need to use Headman headers.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN | Pump & Line Kit |
Return Port Size: | 16mm - 6AN | Steering Shaft Kit |
Pump Required: | Low Flow 1100 psi | Mounting Hardware |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | 8021320 / 8021330 | |
Granada Outer Ends | 8021250 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1967-69 Camaro/1968-74 Nova Power Rack & Pinion Kit, Black
Product# 8010540-01-01
Regular price $1,915.00 Save $-1,915.00Unisteer's kits are based off the stock cross-member and steering linkage. The power rack & pinion is a narrowed GM rack. This is machined so that the internal pivot points match the dimensions of the original center link and control arms on the Camaro front end. This gives you the steering you deserve.
The racks come mounted to a simple one piece bracket that mounts up right behind the stock cross member at the rear lower control arm bolts. Simply slide out the original bolts and replace with the supplied longer bolts to install the rack. The power rack & pinion comes with a new set of bolt-on steering arms which mount to the original spindles and ensure you maintain your turning radius.
These kits can be used with either the factory column or an aftermarket column, Choose whether you want a two or three u-joint shaft kit and what column you want to mount the shaft kit to - factory, 1" DD or 1" - 48 tooth spline. If using the factory column, you will also want to purchase our Factory Column adaptor which bolts into place on the factory column replacing the rag joint and giving you a spline to attach a u-joint.
The Power rack kits have been successfully used on cars with small block and big block motors. Headers can present an issue with clearance for the shaft linkage.
Note: Most aftermarket Heads have raised exhaust floors by 1/4" to 1/2" which does not make clearance any easier.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 5" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 Turns | Mounting Bracket |
Pressure Port Size: | Banjo - 6 AN (lower) | Steering Arms |
Return Port Size: | Banjo - 6AN (upper) | Mounting Hardware |
Pump Required: | Low Flow / Pressure | |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | 10002 |

1967-69 Camaro/1968-74 Nova Manual Rack & Pinion Kit, Black
Product# 8000770-01-01
Regular price $945.00 Save $-945.00Unisteer's kits are based off the stock cross-member and steering linkage. The manual rack is Unisteer's own rack & pinion design. This is machined so that the internal pivot points match the dimensions of the original center link and control arms on the Camaro front end. This gives you the steering you deserve.
The racks come mounted to a simple one piece bracket that mounts up right behind the stock cross member at the rear lower control arm bolts. Simply slide out the original bolts and replace with the supplied longer bolts to install the rack. The manual rack has enough travel that steering arms are not necessary.
These kits can be used with either the factory column or an aftermarket column, Choose whether you want a two or three u-joint shaft kit and what column you want to mount the shaft kit to - factory, 1" DD or 1" - 48 tooth spline. If using the factory column, you will also want to purchase our Factory Column adaptor which bolts into place on the factory column replacing the rag joint and giving you a spline to attach a u-joint.
The Manual rack kits have been successfully used on cars with small block and big block motors. Headers can present an issue with clearance for the shaft linkage.
Note: Most aftermarket Heads have raised exhaust floors by 1/4" to 1/2" which does not make clearance any easier.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 9/16"-26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 3.75 Turns | Mounting Bracket |
Pressure Port Size: | NA | Mounting Hardware |
Return Port Size: | NA | |
Pump Required: | NA | |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | 8020940 |
Click Here to View Installation Instructions

1955-56 Ford Rack & Pinion Kit
Product# 8011640-01
Regular price $2,165.00 Save $-2,165.00This is a rear steer center take-off style rack & pinion with a ball center bar that exactly matches the center link of the stock suspension for the '55-'56 Fords. The rack & pinion comes mounted to a one piece mounting bracket that bolts up to the frame using the same holes that help the steering box and idler arm.
This kit has been successfully installed in cars with both the 272 and 292 motors with stock manifolds. Other headers may work but might require modification or another u-joint in the column linkage.
Note: If you have a 312 or 352 motor our kit may work with modification & different pump bracket which we can supply.
Note: This kit will not work with the factory column shifter, but it will work with an aftermarket column shifter.
Tech Info: |
Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN Banjo | Pump & Line Kit |
Return Port Size: | 16mm - 6AN Banjo | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16"-18 | |
Outer ends: | Included |

Early 1967 Mustang Power Rack & Pinion for Small Block
Product# 8010820-01-01
Regular price $1,700.00 Save $-1,700.00Our early Mustang Rack Kit greatly improves the steering and handling when compared to that old steering box. This is a center take-off style rack and pinion that utilizes an offset ball center bar which duplicates the stock center link; this means that the rack matches the exact geometry of the original front suspension. Effectively eliminating bump steer, and creating great handling.
The rack comes mounted to a one piece mounting bracket which replaces the tubular cross member located directly behind the front suspension. Since the racks are center take-off style, we off set the rack on the mounting bracket; moving the pinions closer to the driver-side frame which makes connection of the steering linkage to a column as easy as possible.
From a steering standpoint, we found that the early Mustangs split mid 1967 and there were slight differences, so make sure you order the correct kit! Additionally, later model Mustangs and Cougars may look the same, but are NOT - check out our Cougar Rack & Pinion Kits.
The kit will work on Small Block cars, and have been successfully used with Stock Manifolds, and Hooker Super Comp Headers. Tri-Y Headers have worked with 289, and 302 engines. Other Headers may work, but we can't guarantee an easy install. This kit requires the use of a mini starter. This kit may require some modifications on Mustangs with Dart Heads and other Aftermarket Heads requiring different headers.
Note: Granada Spindles have been used on these cars. Please indicate this to us with the drop down menu above, so we can swap the outer ends you will need.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN | Pump & Line Kit |
Return Port Size: | 16mm - 6AN | Steering Shaft Kit |
Pump Required: | Low Flow 1100 psi | Mounting Hardware |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | 8021320 / 8021330 | |
Granada Outer Ends | 8021250 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1955-57 Ford Thunderbird Rack and Pinion Kit
Product# 8011690-01
Regular price $2,115.00 Save $-2,115.00This kit is based on a rear steer center take-off style rack & pinion, as are the majority of our kits, but this one is specific to these Thunderbirds. The rack & pinion is mounted to a one piece mounting bracket which bolts to the frame using the same holes for the steering box and the idler arm on the passenger side.
The Unisteer kit was designed to go on a Thunderbird with stock suspension and 272, 292, and 312 motors. Let us know and we can modify the kit to fit popular small block motors, like the 289, 302, and 351 before shipping . Install was done on a vehicle with stock exhaust manifolds. Headers may work, but might need modification.
Let your sales person know, or make the appropriate selection in the menu above to accommodate the right small block motor or an aftermarket column.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN Banjo | Pump & Line Kit |
Return Port Size: | 16mm - 6AN Banjo | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | Provided | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1960-65 Ford Falcon/Comet Power Rack & Pinion Kit, Black
Product# 8010720-01-01
Regular price $1,490.00 Save $-1,490.00Unisteer's Falcon / Comet Power Kit uses a rear steer traditional style rack & pinion that has been machined down to match the stock suspension of the Falcons. This rack comes mounted to a one piece U-shapped bracket that bolts up to the back side of your stock motor / frame mounts. Slide the bracket up into place and install with our longer bolts. If you do not want to deal with a power steering pump, we also have this kit available with a manual unit.
Installs on these cars have been done with stock manifolds or Hooker Super Comp Headers. Other headers may work with modification. Tri-Y style headers do not work. This kit works with V8 motors and floor shifters. This kit will not work with the factory column shifter, but it will work with an aftermarket column shifter. If you have a different engine, let us know and we will try to accommodate you with a different pump bracket.
This kit is designed to work with 1963-64 Ford Falcon/Comet V-8 spindles. Other year Falcon/Comet spindles may not work. Cars with Granada spindles will NOT work.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 5.25" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 Turns | Mounting Bracket |
Pressure Port Size: | Banjo 6 AN (Lower) | Pump & Line Kit |
Return Port Size: | Banjo 6 AN (Upper) | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16"-18 | |
Outer ends: | 8027450 |
Click Here to Look at Product Instructions

1964-67 Pontiac GTO / Lemans / Tempest Rack & Pinion Kit
Product# 8012170-01-01
Regular price $1,765.00 Save $-1,765.00This kit was specifically designed to fit the Pontiac GTO / Tempest / Lemans. This is a front steer center take-off style Rack & Pinion mounted on a 5/16" plate bracket that bolts in to the same mounting holes used for the factory steering box and idler arm. The rack matches the stock suspension on these cars, replacing the original center link. The kit will clear Z-Bar and 4 Speed Linkage. It will also clear stock manifolds, or Hooker Competition Headers. Other Headers may work, but might require modifications.
Note: Pump does not work with stock air conditioning.
Note: Some aftermarket heads may have raised exhaust floors and may change your header height causing steering shaft interference, which may need modification.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 3/4"-36 Spline | Rack & Pinion |
Amount of Travel: | 7" | Outer Tie Rod Ends |
Turns Lock to Lock: | 3 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6 AN Banjo | Pump & Line Kit |
Return Port Size: | 16mm - 8 AN Banjo | Steering Shaft Kit |
Pump Required: | High Flow / Pressure | Mounting Hardware |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | 8020940 |
Click Here to Look at Product Instructions

1965-66 Mustang Manual Rack & Pinion
Product# 8001110-01-01
Regular price $1,275.00 Save $-1,275.00Our early Mustang Rack Kit greatly improves the steering and handling when compared to that old steering box. This is a center take-off style rack and pinion that utilizes an offset ball center bar which duplicates the stock center link; this means that the rack matches the exact geometry of the original front suspension. Effectively eliminating bump steer, and creating great handling.
The rack comes mounted to a one piece mounting bracket which replaces the tubular cross member located directly behind the front suspension. Since the racks are center take-off style, we off set the rack on the mounting bracket; moving the pinions closer to the driver-side frame which makes connection of the steering linkage to a column as easy as possible.
Later model Mustangs and Cougars may look the same, but are NOT - check out our Cougar Rack & Pinion Kits.
The kit will work on Big Block and Small Block cars, and have been successfully used with Stock Manifolds, and Hooker Super Comp Headers. Other Headers may work, but we can't guarantee an easy install. This kit requires the use of a mini starter. This kit may require some modifications on Mustangs with Dart Heads and other Aftermarket Heads requiring different headers.
Note: Granada Spindles have been used on these cars. Please indicate this to us with the drop down menu above, so we can swap the outer ends you will need.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | Maval - 9/16" - 26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 4.5 Turns | Mounting Bracket |
Pressure Port Size: | NA | Steering Shaft Kit |
Return Port Size: | NA | Mounting Hardware |
Pump Required: | NA | |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | 8021120 / 8021300 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1928-32 Ford Cross Steer® Retro-Fit Kit, Black Bracket
Product# 8000470-01
Regular price $485.00 Save $-485.00The Cross Steer is essentially a small half rack and pinion that bolts into place exactly where the Vega style steering box would bolt on. The system still uses a draglink between both wheels. The Cross Steer was specifically designed for solid axle cars and trucks of this era with a mono leaf spring suspension. Since the Cross Steer pivots only off the one side, it matches up perfectly with the stock suspension of the solid axle Fords. Sorry, it will not work on Chevys which had dual leaf springs.
Note: You must have split wishbones (at least 12 inches) or hairpins for the Cross Steer to properly work.
The gear comes mounted to an angled bracket that has the same three hole pattern for mounting the Vega box. This small rack & pinion is made of all automotive grade components and can handle a vehicle up to 3500 lbs!
If you are building a new vehicle, the regular Cross Steer is the best option and you can run your steering linkage down to the gear. We can even send you a Cross Steer with a plain steel bracket that you could weld to your frame and paint to match. If you still have a Vega Box, check out our retrofit that has a shaft kit. This shaft kit consists of a coupler and a shaft with a splined end which is the same size as the Vega spline so you can reuse your existing steering linkage. The switch over can be done in only an hour or two!
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 9/16"-26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Mounting Bracket |
Turns Lock to Lock: | 3.75 Turns | Mounting Hardware |
Pressure Port Size: | NA | Steering Shaft Kit |
Return Port Size: | NA | |
Pump Required: | NA | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |
Inner End Threads: | Tube & Adapter 11/16"-18 | Click here for IDIDIT Columns for your Streetrod! |

1960-66 Chevy C10 w/Discs Power Rack & Pinion Kit
Product# 8011920-01-01
Regular price $1,515.00 Save $-1,515.00On this kit we used a traditional style rear steer rack & pinion that is mounted to a one piece bracket which bolts up to the outside of either frame rail in the same holes as the original steering box and idler arms.
This kit is for rear wheel drive vehicles only, NOT 4x4s. Installs have been done on V-8s, so there should be room if using a 6 Cylinder. There is quite a bit of room for the shaft support, but some headers may require modification. A two groove pulley on your water pump is required for this kit.
Note: If using drum brake spindles order kit 8011740-01.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 3/4"-DD | Rack & Pinion |
Amount of Travel: | 5.75" | Mounting Bracket |
Turns Lock to Lock: | 2 7/8 Turns | Pump & Line Kit |
Pressure Port Size: | Straight to #6 AN (upper) | Steering Shaft Kit |
Return Port Size: | Straight to #6 AN (lower) | Mounting Hardware |
Pump Required: | Low Flow | Outer Tie Rod Ends |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | 8026690 |
Click Here to Look at Product Instructions

1955-57 Chevy Power Rack & Pinion Kit
Product# 8010600-01
Regular price $1,632.00 Save $-1,632.00We used a modified traditional style GM rack and pinion for the Tri-5s. The rack is bolted to a one piece bracket which mounts exactly where the old steering box and idler arm were mounted to the frame. The rack is machined so it is narrower, matching the stock suspension of these cars.
This kit is designed for use on cars with small block motors with headers; Sanderson and FlowTech headers have been successfully used. However, they do not work with a mechanical clutch, you will need to switch to a hydraulic clutch to install these headers. Other headers may work as well, but may require modification or a shaft kit with three u-joints. Installs on Big Block Motors have been done, but are more difficult as it will require three u-joints, a support bearing, and probably modification to the headers. This kit has been used for big block, as well as LS1, LSX, and ZZ4 motors (with modifications), in which the bracket is slightly different by changing the location of the rack for more clearance for oil pans. This rack kit will also work with Mike McGuagthy's drop spindles with slight modification to the inner ends. Please call us for more info.
The rack does have less travel than the old pitman arm, so the arms are necessary to maintain comparable turning radius. Pump kits built how you want, and matched to run with the rack & pinion are available, but sold separately. due to variations. Check out our pump options. We also have shaft kits for small block motor cars, which consist of two joints, DD shafting, and a coupler for aftermarket columns or a bearing to reuse the Factory Column.
Unisteer is also pleased to offer Ididit Columns as well as Sanderson and Flow Tech Headers.
Note: This unit is designed for Floor Shift vehicles. If you would like to use a column shift, you will need to upgrade the column to an Ididit column.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 16mm DD | Rack & Pinion |
Amount of Travel: | 5" | Mounting Bracket |
Turns Lock to Lock: | 2.5 Turns | Mounting Hardware |
Pressure Port Size: | M14 Banjo - 6 AN | Steering Arms |
Return Port Size: | M16 Banjo - 6 AN | |
Pump Required: | Low Flow | |
Inner End Threads: | M14 x 1.5 | |
Outer End Threads: | 10002 |
Click Here to View Installation Instructions
Click Here for IDIDIT Tri-5 Columns

1960-64 Ford Rack & Pinion Kit for Traditional Motors
Product# 8011410-01
Regular price $1,765.00 Save $-1,765.00This is a rear steer center take-off style rack and pinion with a ball center bar that exactly matches the center link of the stock suspension for the '60-'64 Fords. The rack & pinion comes mounted to a one piece mounting bracket that bolts up to the frame using the same holes that held up the steering box and idler arm.
This is designed to be used with Traditional FE Motors found in these cars, including the 332, and 352. This kit has been installed on vehicles with stock manifolds. Other Headers may work, but might require modification or another u-joint in the column linkage.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN Banjo | Pump & Line Kit |
Return Port Size: | 16mm - 6AN Banjo | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16"-18 | |
Outer ends: | Included |

1968-72 GM A-Body Rack Only Kit
Product# 8010700-01
Regular price $1,150.00 Save $-1,150.00This kit is made for the Chevelles and other GM A-Body cars. In these years of Chevelles, we used a front steer center take off style rack and pinion on a one piece bracket that bolts up in the same location as the original steering box and idler arm. This kit does clear the Z-Bar and 4 Speed Linkage. We have installed this kit on cars with both big block and small block motors. On the Big Block, stock manifolds and Super Comp Headers work, and on the Small Block motor Hooker Comp Headers work. Other headers may work, but may need modification.
The kit is set up to go on cars with either small blocks or big blocks with long water pumps. If you have a short water pump, we can easily accommodate, but you will need to call us, and we'll swap in the proper components.
Note: Some aftermarket cylinder heads may have a raised exhaust floor anywhere from 0.25" - 0.4" which may also affect your header location.
Note: This kit will also bolt into a 1968-72 small block El Camino and Monte Carlo.
A special note on big block motors: There are several different designs, Mark IV, Mark V, and Mark VI. The original Mart IV design has a deck height of 9.8", the Mark V and Mark VI designs have a deck height of 10.2". The 0.4" difference affects clearance on these big block cars. Mark V and Mark VI designed cars will probably need more header modification.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 3/4" - 36 Spline | Rack & Pinion |
Amount of Travel: | 7" | Mounting Bracket |
Turns Lock to Lock: | 3 Turns | Mounting Hardware |
Pressure Port Size: | 18mm - 6 AN | |
Return Port Size: | 16mm - 8AN | |
Pump Required: | High Flow / Pressure | |
Inner End Threads: | M14 x 1.5 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |
Outer End Threads: | 8020940 | Cick here to look at ididit Chevelle Columns |

1962-67 Chevy II/Nova Power Rack & Pinion Kit (Black Rack)
Product# 8010650-01-01
Regular price $2,035.00 Save $-2,035.00As with all of Unisteer's rack kits, the foundation of the Chevy II kits are rack & pinions matched to the stock suspension of these cars. This kit is designed to work with Small Block engines. The power rack and pinion is a matched GM rack manufactured to the correct dimensions. This kit comes mounted to a one piece bracket. The Bracket mounts behind the front engine mounts - slide out the original hardware and replace with the longer bolts supplied to mount up the kit.
The kits have been successfully installed on cars with stock manifolds, and Headman Headers. Otherwise, custom headers or modification to your headers will be needed. Rear sump oil pans and pickups must also be used so the rack will clear. The kits will work only with factory stock floor shift columns or aftermarket floor shift columns. Each kit includes a column bracket, firewall gasket, and column bearing, everything necessary to modify an original column. The power rack & pinion kit also includes a GM Type II pump kit with remote reservoir, single V-groove pulley, and braided stainless lines.
Steering arms are included in this kit as the racks do not have the same travel as the box and that big old pitman arm. The steering arms replace the bolt on ones on your spindles, but are shorter than the originals giving you back the turning radius.
No shaft kits are included due to the amount of variations, but we certainly can supply you with U-joints and shafting.
Note: On some aftermarket engine blocks, the deck height may be raised by 0.4". This may affect your exhaust header location.
Note: Some aftermarket cylinder heads may have a raised exhaust floor anywhere from 0.25" - 0.4" which may affect header height.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 17mm DD GM | Rack & Pinion |
Amount of Travel: | 5" | Mounting Bracket |
Turns Lock to Lock: | About 2.5 Turns | Mounting Hardware |
Pressure Port Size: | 16mm - 6AN | Steering Arms |
Return Port Size: | 18mm 8AN | Pump & Line Kit |
Pump Required: | Provided - Low Flow | |
Inner End Threads: | M14 x 1.5 | |
Outer End Threads: | 10002 |
Click Here to View Installation Instructions
Click here for IDIDIT Nova & Chevy II Columns

1968-72 GM A-Body Big Block Long Water Power Rack and Pinion Kit
Product# 8010740-01-01
Regular price $1,775.00 Save $-1,775.00This kit is made for the Chevelles and other GM A-Body cars. In these years of Chevelles, we used a front steer center take off style rack and pinion on a one piece bracket that bolts up in the same location as the original steering box and idler arm. This kit does clear the Z-Bar and 4 Speed Linkage. We have installed this kit on cars with both big block and small block motors. On the Big Block, stock manifolds and Super Comp Headers work, and on the Small Block motor Hooker Comp Headers work. Other headers may work, but may need modification.
The kit is set up to go on cars with either small blocks or big blocks with long water pumps. If you have a short water pump, we can easily accommodate, but you will need to call us, and we'll swap in the proper components.
Note: Some aftermarket cylinder heads may have a raised exhaust floor anywhere from 0.25" - 0.4" which may also affect your header location.
Note: This kit will also bolt into a 1968-72 small block El Camino and Monte Carlo.
A special note on big block motors: There are several different designs, Mark IV, Mark V, and Mark VI. The original Mart IV design has a deck height of 9.8", the Mark V and Mark VI designs have a deck height of 10.2". The 0.4" difference affects clearance on these big block cars. Mark V and Mark VI designed cars will probably need more header modification.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 3/4" - 36 Spline | Rack & Pinion |
Amount of Travel: | 7" | Mounting Bracket |
Turns Lock to Lock: | 3 Turns | Pump & Line Kit |
Pressure Port Size: | 18mm - 6 AN | Steering Shaft Kit |
Return Port Size: | 16mm - 8AN | Mounting Hardware |
Pump Required: | High Flow / Pressure | |
Inner End Threads: | M14 x 1.5 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |
Outer End Threads: | 8020940 | Cick here to look at ididit Chevelle Columns |

1978-88 GM G-Body Rack & Pinion Kit
Product# 8012400-01-01
Regular price $1,665.00 Save $-1,665.00The G-body kit is a front steer rack and is bolted to a one piece bracket that mounts to the inside of your frame rails. It utilizes the same bolt holes that your steering box and idler arm were attached to. The kit was designed to match the stock pivot points on the vehicle which will not only make it handle well, but also reduce bump steer. The pump with mounting bracket for small block applications, the u-joints, steering shafts and sway bar link kits are all there to get it done quickly and easily. This unit has fit with Hooker Competition, and Super Competition headers.
Note: On some aftermarket engine blocks, the deck height may be raised by up to 0.4". This may affect your exhaust header location.
Note: Some aftermarket cylinder heads may have a raised exhaust floor, anywhere from 0.25"-0.4" which may also affect your header locations.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 3/4"-36 Spline | Rack & Pinion |
Amount of Travel: | 7" | Outer Tie Rod Ends |
Turns Lock to Lock: | 3 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN Banjo | Pump & Line Kit |
Return Port Size: | 16mm - 6AN Banjo | Steering Shaft Kit |
Pump Required: | High Flow/Pressure | Mounting Hardware |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | 8020940 |
Click Here to Look at Product Instructions

1933-34 Ford Cross Steer® New Build (No Shaft Kit) Black Bracket
Product# 8000680
Regular price $450.00 Save $-450.00The Cross Steer is essentially a small half rack and pinion that bolts into place exactly where the Vega style steering box would bolt on. The system still uses a draglink between both wheels. The Cross Steer was specifically designed for solid axle cars and trucks of this era with a mono leaf spring suspension. Since the Cross Steer pivots only off the one side, it matches up perfectly with the stock suspension of the solid axle Fords. Sorry, it will not work on Chevys which had dual leaf springs.
Note: You must have split wishbones (at least 12 inches) or hairpins for the Cross Steer to properly work.
The gear comes mounted to an angled bracket that has the same three hole pattern for mounting the Vega box. This small rack & pinion is made of all automotive grade components and can handle a vehicle up to 3500 lbs!
If you are building a new vehicle, the regular Cross Steer is the best option and you can run your steering linkage down to the gear. We can even send you a Cross Steer with a plain steel bracket that you could weld to your frame and paint to match. If you still have a Vega Box, check out our retrofit that has a shaft kit. This shaft kit consists of a coupler and a shaft with a splined end which is the same size as the Vega spline so you can reuse your existing steering linkage. The switch over can be done in only an hour or two!
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 9/16"-26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Mounting Bracket |
Turns Lock to Lock: | 3.75 Turns | Mounting Hardware |
Pressure Port Size: | NA | |
Return Port Size: | NA | |
Pump Required: | NA | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |
Inner End Threads: | Tube & Adapter 11/16"-18 | Click here for IDIDIT Columns for your Streetrod! |

1963-65 Fairlane Rack & Pinion Kit for Popular Small Blocks
Product# 8011570-01
Regular price $1,790.00 Save $-1,790.00This kit uses a rear steer center take off rack & pinion mounted to a solid one piece bracket which bolts up to the frame using the original holes for the steering box and Idler Arm. This kit works with Small Block Motor cars only. It will fit with the 221, 260, 289, 302, and 351W motors. Installs have been done using Hooker Long Tube Headers or Competition Headers. Other headers may work, but may require modification.
Note: This kit will not work with the factory column shifter, but it will work with an aftermarket column shifter.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN Banjo | Pump & Line Kit |
Return Port Size: | 16mm - 6AN Banjo | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16"-18 | |
Outer ends: | Included | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1967-70 Cougar Power Rack & Pinion Kit
Product# 8011940-01-01
Regular price $1,700.00 Save $-1,700.00The Cougar Rack kit eliminates slop and greatly improves the steering and handling of your vehicle. This rack is a center take-off style rack and pinion that utilizes an offset ball center bar which duplicates the stock center link; this means that the rack matches the exact geometry of the original front suspension.
The rack comes mounted to a one piece mounting bracket which replaces the tubular cross member located directly behind the front suspension. Since the racks are center take-off style, we offset the rack on the mounting bracket moving the pinions closer to the driver-side frame, which makes connection of the steering linkage to the column as easy as possible. The set up will clear 4-speed linkage, and Z-Bar. This kit will require the use of a mini starter.
This kit will work with both a big block and small block cars, and has been successfully used with Stock Manifolds and Hooker Super Competition Headers. The rack may require modifications on vehicles with Dart Heads, or other Aftermarket Heads.
Note: Please use the drop down menus above to help us provide the proper components for your build.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5-2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm Banjo - 6 AN | Pump & Line Kit |
Return Port Size: | 16mm Banjo - 6 AN | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16"-18 | |
Outer ends: | 8021320 / 8021330 | |
Granada Option | 8021250 |
Click Here to Look at Product Instructions

1979-93 Ford Mustang Power Quick Ratio, Plain
Product# 8010080
Regular price $399.00 Save $-399.00This kit has everything you need to switch over to a quick ratio power rack & pinion. This kit is rebuilt to be better than new. This kit is also available in a standard ratio 8010020. This power rack and pinion comes with Unisteer's Limited Lifetime Warranty. This unit is a low flow unit that uses port sizes of 5/8" and 9/16"
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 3/4"-36 w/ Milled Flat | Rack & Pinion |
Amount of Travel: | 5.375" | |
Turns Lock to Lock: | 2.5 Turns | |
Pressure Port Size | 5/8" | |
Return Port Size | 9/16" | |
Pump Required | Low Flow / Pressure | |
Inner End Threads: | 9/16"-18 | |
Mounting Boss | 15.5" |

1994-04 Ford Mustang Manual Conversion Kit Standard Ratio
Product# 8000950
Regular price $550.00 Save $-550.00This kit has everything you need to convert from power steering to standard ratio manual steering. Drop the weight and power drain of a Power Rack & Pinion and Power Steering Pump.

1960-65 Ford Falcon/Comet Manual Rack & Pinion Kit, Black
Product# 8001050-01
Regular price $1,350.00 Save $-1,350.00One of Unisteer's own builds, we used a center take off style rack mounted to a one piece U-shapped bracket that bolts up to the back side of your stock motor / frame mounts. Slide the bracket up into place and install with our longer bolts.
Installs on these cars have been done with stock manifolds or Hooker Super Comp Headers. Other headers may work with modification. Tri-Y style headers do NOT work. This kit works with V8 motors and floor shifters. This kit will not work with the factory column shifter, but it will work with an aftermarket column shifter.
If your Falcon or Comet had inline 6, the spindles have a different taper, just let us know and we can get you a different set of outers.
Note: We have run into cars with Granada spindles, and this kit will NOT work with those spindles.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 9/16"-26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 3.75 Turns | Mounting Bracket |
Pressure Port Size: | NA | Steering Shaft Kit |
Return Port Size: | NA | Mounting Hardware |
Pump Required: | NA | |
Inner End Threads: | 9/16"-18 | |
Outer ends: | Included | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1957-59 Ford Rack & Pinion Kit for Popular Small Blocks
Product# 8011430-01
Regular price $1,850.00 Save $-1,850.00This is a rear steer center take-off style rack and pinion with a ball center bar that exactly matches the center link of the stock suspension for the '57-'59 Fords. The rack & pinion comes mounted to a one piece mounting bracket that bolts up to the frame using the same holes that held the steering box and idler arm.
This kit is designed for use with Windsor Small Block Motors, the 289, 302, and 351. This kit has been installed on vehicles with stock manifolds. Other Headers may work, but might require modification or another u-joint in the column linnkage.
Note: This kit will not work with the factory column shifter, but it will work with an aftermarket column shifter.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN Banjo | Pump & Line Kit |
Return Port Size: | 16mm - 6AN Banjo | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16"-18 | |
Outer ends: | Included | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1960-66 Chevy C10 w/Drums Power Rack & Pinion Kit
Product# 8011740-01-01
Regular price $1,515.00 Save $-1,515.00On this kit we used a traditional style rear steer rack & pinion that is mounted to a one piece bracket which bolts up to the outside of either frame rail in the same holes as the original steering box and idler arms.
This kit is for rear wheel drive vehicles only, NOT 4x4s. Installs have been done on V-8s, so there should be room if using a 6 Cylinder. There is quite a bit of room for the shaft support, but some headers may require modification. A two groove pulley on your water pump is required for this kit.
Note: If using disk brake spindles order kit 8011920-01.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 3/4"-DD | Rack & Pinion |
Amount of Travel: | 5.75" | Mounting Bracket |
Turns Lock to Lock: | 2 7/8 Turns | Pump & Line Kit |
Pressure Port Size: | Straight to #6 AN (upper) | Steering Shaft Kit |
Return Port Size: | Straight to #6 AN (lower) | Mounting Hardware |
Pump Required: | Low Flow | Outer Tie Rod Ends |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | 8020940 |
Click Here to Look at Product Instructions

1978-83 Power Dodge/Plymouth Omni Replacement Rack (Rear Steer)
Product# 8012300
Regular price $449.00 Save $-449.00As the traditional Dodge/Plymouth Omni Rear Steer rack and pinions are difficult to find and rebuild, Unisteer has come up with a replacement rack. Our Omni replacement rack uses a GM rack that has been custom made to the same specifications as the old Omni. This includes a custom mounting bracket to replicate how the original OEM Omni mounted. The rack is rebuilt to the highest quality to be better than new. These gears come with a black powder coated tube, making for a very nice finish. The Omni replacement power rack and pinions come with Unisteer's Limited Lifetime Warranty.
Note: There are a number of different options regarding overall size, and tie rod threads, call us for availability at 1-855-248-9110. Also, The pinion spline is different from stock. It's size is 16mm-DD, so U-Joint 8050260 will be needed.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 16mm - DD | Rack & Pinion |
Amount of Travel: | 5" | |
Turns Lock to Lock: | 2 7/8 Turns | |
Pressure Port Size | M14 Banjo - 6AN | |
Return Port Size | M16 Banjo - 6AN | |
Pump Required | Low Flow / Pressure |

1994-04 Ford Mustang Manual Conversion Kit Quick Ratio
Product# 8000960
Regular price $550.00 Save $-550.00This kit has everything you need to convert from power steering to quick ratio manual steering. Drop the weight and power drain of a Power Rack & Pinion and Power Steering Pump.

1935-40 Ford Cross Steer®
Product# 8000510
Regular price $550.00 Save $-550.00The Cross Steer is essentially a small half rack and pinion that bolts into place exactly where the steering box would bolt on. The system still uses a draglink between both wheels. The Cross Steer was specifically designed for solid axle cars and trucks of this era. This specific Cross Steer us very similar to our '28-'32 Ford Cross Steer - the gear is essentially the same, but with a slightly slower ratio to accommodate these larger vehicles. The biggest difference is the mounting bracket; the large mounting bracket actually bolts up in between the frame rails on these Fords. A boxed frame will have to be opened up to accommodate the bracket. The bracket does hang down lower, so this Cross Steer will only work on cars with the stock axle or a 2" drop axle, it will not work with 4" drop axles.
The rack comes mounted to the bracket with drag link tube and mounting hardware. You will also need some U-joints and a shaft to connect down to the pinion. This manual rack will handle vehicles around 3500 lbs, check with engineering for any heavier applications.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 9/16"-26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Mounting Bracket |
Turns Lock to Lock: | 4.5 - 1.3 Ratio | Mounting Hardware |
Pressure Port Size: | NA | |
Return Port Size: | NA | |
Pump Required: | NA | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |
Inner End Threads: | Tube & Adapter 11/16"-18 | Click here for IDIDIT Columns for your Streetrod! |

1964-67 GM A-Body Big Block Short Water Power Rack and Pinion Kit
Product# 8010780-01-01
Regular price $1,875.00 Save $-1,875.00This kit was specifically designed to fit Chevy A-Body cars. This is a front steer center take off style rack & pinion mounted on a one piece bracket that bolts in the same mounting holes used for the factory steering box and idler arm. The rack matches the stock suspension on these cars replicating the original center link.
The kit clears the Z-Bar and 4 Speed Linkage. The kit has been used on both Small Block and Big Block motor cars. Stock Manifolds work with both motors and on Big Blocks, we have used Super Comp Headers while on Small Block Motors, Hooker Competition Headers have been used. Other headers may work, but may need modification.
Shaft kits are included in both small block and big block kits, and require using 3 u-joints and support bearing. Pump kits are also included; the big block motor pump kit uses a matched pump, single V-groove pulley, bracket, and remote reservoir. The small block , motor pump kit includes a matched pump, single V-groove pulley, bracket, and clip-on reservoir.
Note: Most Aftermarket Heads have raised exhaust floors by 1/4" to 1/2" which does not make clearance any easier.
Note: This kit will also bolt into a 1964-67 big block El Camino.
A special note on big block motor cars: There are several different designs, Mark IV, Mark V, and Mark VI. The original Mark IV design has a deck height of 9.8", the Mark V and Mark VI designs have a deck height of 10.2". The 0.4" difference affects clearance on these big block cars. Mark V and Mark VI designed cars will probably need header modification.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 3/4" - 36 Spline | Rack & Pinion | ||
Amount of Travel: | 7" | Mounting Bracket | ||
Turns Lock to Lock: | 3 Turns | Pump & Line Kit | ||
Pressure Port Size: | 18mm - 6 AN | Steering Shaft Kit | ||
Return Port Size: | 16mm - 8AN | Mounting Hardware | ||
Pump Required: | High Flow / Pressure | |||
Inner End Threads: | M14 x 1.5 | Outer End Threads: | 8020940 | Click here for IDIDIT Chevelle Columns |

1957-59 Ford Rack & Pinion Kit for Traditional Motors
Product# 8011400-01
Regular price $1,790.00 Save $-1,790.00This is a rear steer center take-off style rack and pinion with a ball center bar that exactly matches the center link of the stock suspension for the '57-'59 Fords. The rack & pinion comes mounted to a one piece mounting bracket that bolts up to the frame using the same holes that held the steering box and idler arm.
This kit is designed for use with Traditional FE Block Motors found with these cars, the Ford 332 and 352. This kit has been installed on vehicles with stock manifolds. Other Headers may work, but might require modification or another u-joint in the column linkage.
Note: This kit will not work with the factory column shifter, but it will work with an aftermarket column shifter.
Tech Info: |
Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN Banjo | Pump & Line Kit |
Return Port Size: | 16mm - 6AN Banjo | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16"-18 | |
Outer ends: | Included |
Click Here to Look at Product Instructions

1963-82 Corvette Power Rack and Pinion Kit
Product# 8011540-01
Regular price $1,250.00 Save $-1,250.00Unisteer's Power Rack kits utilize center take off style rear steer rack & pinions with a ball center which matches the original center link for these Vettes. Geometrically correct - No Bump Steer! The racks come on one piece mounting brackets which bolt on using the same factory holes for the steering box and idler arm. These kits clear the Z-Bar and 4 Speed Linkage with no problem. The kits have worked on Small Block motor cars with stock manifolds, short or long tube headers.
Pump and Shaft Kits are not included in the basic rack kits due to differences in the year break down for Vettes. We do recommend trying our pump and shaft kit, but that is up to you.
Nore: This kit will not work with 68'-82' Big Block applications.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD GM | Rack & Pinion |
Amount of Travel: | 6" | Mounting Bracket |
Turns Lock to Lock: | 2.5-2.75 Turns | Mounting Hardware |
Pressure Port Size: | 18mm - 6AN Banjo (Lower) | |
Return Port Size: | 16mm - 6AN Banjo (Upper) | |
Pump Required: | Low Flow / Pressure | |
Inner End Threads: | 14mm x 1.5 | |
Outer End Threads: | 8020940 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1949-51 Ford Power Rack & Pinion Kit
Product# 8011660-01
Regular price $2,165.00 Save $-2,165.00Our kit is designed to fit in your stock Ford. It uses a one piece folded steel bracket that bolts in place where your idler arm and steering box used to be. It follows the same pivot points as your stock geometry therefor eliminating bump steer. The headers provided in the kit must be used in your install. There isn't any loss in the factory turning radius. The pump kit is matched to the rack & pinion providing the correct flow and pressure for the optimal driving experience.
Note: Granada spindles have been used on this vehicle from time to time. If you have these, let us know with the drop down menu above so we can swap out the proper outer ends. Does not work with Automatic Columns.
If you do not wish to purchase the kit without headers, please purchase kit 8012540.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 5.25" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 Turns | Mounting Bracket |
Pressure Port Size: | 6AN Banjo (Lower) | Pump & Line Kit |
Return Port Size: | 6AN Banjo (Upper) | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16"-18 | Headers |
Outer ends: | Included | |
Granada Outer Ends | 8021250 |
Click Here to Look at Product Instructions

Late 1967-70 Power Mustang Rack & Pinion Kit for Big Blocks
Product# 8010920-01-01
Regular price $1,750.00 Save $-1,750.00Our early Mustang Rack Kit greatly improves the steering and handling when compared to that old steering box. This is a center take-off style rack and pinion that utilizes an offset ball center bar which duplicates the stock center link; this means that the rack matches the exact geometry of the original front suspension. Effectively eliminating bump steer, and creating great handling.
The rack comes mounted to a one piece mounting bracket which replaces the tubular cross member located directly behind the front suspension. Since the racks are center take-off style, we off set the rack on the mounting bracket; moving the pinions closer to the driver-side frame which makes connection of the steering linkage to a column as easy as possible.
From a steering standpoint, we found that the early Mustangs split mid 1967 and there were slight differences, so make sure you order the correct kit! Additionally, later model Mustangs and Cougars may look the same, but are NOT - check out our Cougar Rack & Pinion Kits.
The kit will work on Big Block cars, and have been successfully used with Stock Manifolds, and Hooker Super Comp Headers. Other Headers may work, but we can't guarantee an easy install. This kit requires the use of a mini starter. This kit may require some modifications on Mustangs with Dart Heads and other Aftermarket Heads requiring different headers.
Note: Granada Spindles have been used on these cars. Please indicate this to us with the drop down menu above, so we can swap the outer ends you will need. Also, If you have a 351C motor you will need to use Headman headers.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN | Pump & Line Kit |
Return Port Size: | 16mm - 6AN | Steering Shaft Kit |
Pump Required: | Low Flow 1100 psi | Mounting Hardware |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | 8021320 / 8021330 | |
Granada Outer Ends | 8021250 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1965-67 Ford Galaxie 500 Rack & Pinion Kit
Product# 8012350-01-01
Regular price $1,815.00 Save $-1,815.00This is a rear steer center take-off style rack and pinion with a ball center bar that exactly matches the center link of the stock suspension for the '65-'67 Ford Galaxie 500. The rack & pinion comes mounted to a one piece mounting bracket that bolts up to the frame using the same holes that held up the steering box and idler arm.
This is designed to be used with Traditional Motors found in these cars, including 428, 390, & 352 engines. This kit has been installed on vehicles with stock manifolds. Other Headers may work, but might require modification or another u-joint in the column linkage.
Note: Granada Spindles have been used on these vehicles from time to time. If you have these, let us know in the drop down menu above, so we can swap out the correct outer ends.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN Banjo | Pump & Line Kit |
Return Port Size: | 16mm - 6AN Banjo | Steering Shaft Kit |
Pump Required: | Low Flow / Pressure | Mounting Hardware |
Inner End Threads: | 9/16"-18 | |
Outer ends: | Included | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1994-2004 Ford Mustang Manual QuickRatio (rack only)
Product# 8000580
Regular price $299.00 Save $-299.00Convert your 1994-2004 FORD MUSTANG from power steering to QUICK RATIO manual steering! Drop the weight and power drain of a Power Rack & Pinion and Power Steering Pump!

1967-69 Camaro/1968-74 Nova Power Rack & Pinion Kit, Chrome
Product# 8010540-02-01
Regular price $2,140.00 Save $-2,140.00Unisteer's kits are based off the stock cross-member and steering linkage. The power rack & pinion is a narrowed GM rack. This is machined so that the internal pivot points match the dimensions of the original center link and control arms on the Camaro front end. This gives you the steering you deserve.
The racks come mounted to a simple one piece bracket that mounts up right behind the stock cross member at the rear lower control arm bolts. Simply slide out the original bolts and replace with the supplied longer bolts to install the rack. The power rack & pinion comes with a new set of bolt-on steering arms which mount to the original spindles and ensure you maintain your turning radius.
These kits can be used with either the factory column or an aftermarket column, Choose whether you want a two or three u-joint shaft kit and what column you want to mount the shaft kit to - factory, 1" DD or 1" - 48 tooth spline. If using the factory column, you will also want to purchase our Factory Column adaptor which bolts into place on the factory column replacing the rag joint and giving you a spline to attach a u-joint.
The Power rack kits have been successfully used on cars with small block and big block motors. Headers can present an issue with clearance for the shaft linkage.
Note: Most aftermarket Heads have raised exhaust floors by 1/4" to 1/2" which does not make clearance any easier.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 5" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 Turns | Mounting Bracket |
Pressure Port Size: | Banjo - 6AN (lower) | Steering Arms |
Return Port Size: | Banjo - 6AN (upper) | Mounting Hardware |
Pump Required: | Low Flow / Pressure | |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | 10002 |

1964-67 GM A-Body Small Block Long Water Power Rack and Pinion Kit
Product# 8010790-01-01
Regular price $1,775.00 Save $-1,775.00This kit was specifically designed to fit Chevy A-Body cars. This is a front steer center take off style rack & pinion mounted on a one piece bracket that bolts in the same mounting holes used for the factory steering box and idler arm. The rack matches the stock suspension on these cars replicating the original center link.
The kit clears the Z-Bar and 4 Speed Linkage. The kit has been used on both Small Block and Big Block motor cars. Stock Manifolds work with both motors and on Big Blocks, we have used Super Comp Headers while on Small Block Motors, Hooker Competition Headers have been used. Other headers may work, but may need modification.
Shaft kits are included in both small block and big block kits, and require using 3 u-joints and support bearing. Pump kits are also included; the big block motor pump kit uses a matched pump, single V-groove pulley, bracket, and remote reservoir. The small block , motor pump kit includes a matched pump, single V-groove pulley, bracket, and clip-on reservoir.
Note: Most Aftermarket Heads have raised exhaust floors by 1/4" to 1/2" which does not make clearance any easier.
Note: This kit will also bolt into a 1964-67 small block El Camino.
A special note on big block motor cars: There are several different designs, Mark IV, Mark V, and Mark VI. The original Mark IV design has a deck height of 9.8", the Mark V and Mark VI designs have a deck height of 10.2". The 0.4" difference affects clearance on these big block cars. Mark V and Mark VI designed cars will probably need header modification.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 3/4" - 36 Spline | Rack & Pinion |
Amount of Travel: | 7" | Mounting Bracket |
Turns Lock to Lock: | 3 Turns | Pump & Line Kit |
Pressure Port Size: | 18mm - 6 AN | Steering Shaft Kit |
Return Port Size: | 16mm - 8AN | Mounting Hardware |
Pump Required: | High Flow / Pressure | |
Inner End Threads: | M14 x 1.5 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |
Outer End Threads: | 8020940 | CLICK HERE TO LOOK AT IDIDIT CHEVELLE COLUMNS |

1958-64 Impala/Bel Air Small Block Short Water Rack and Pinion Kit
Product# 8011040-01-01
Regular price $1,650.00 Save $-1,650.00This is a front steer center take off style rack & pinion that matches the stock front end and suspension. The rack is mounted to a one piece mounting bracket that bolts into the same factory holes for the steering box and idler arm. The kit does clear the Z Bar and 4 speed linkage, but does not work with the factory 348 & 409 Engines. If your vehicle had factory power steering, you will need to use our stabilizer bar mounts which are included in place of the factory mounts.
Our kit probably will not work with aftermarket suspension that change the original suspension, but give us a call!
This kit works on most small block engine applications with short water pumps. Installs have been done successfully using Hooker Long Tube Headers. The kits are complete with a shaft kit which includes two u-joints and shafting as well as a pump kit with a pump matched to the gear, clip on reservoir, and Single V-Groove Pulley. Serpentine Pulleys are also available. Pump kits for Long Water Pumps are also available.
Note: Kit can be adapted to fit your needs by selecting the pulley option above.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 3/4" - 36 Spline | Rack & Pinion |
Amount of Travel: | 7" | Outer Tie Rod Ends |
Turns Lock to Lock: | 3 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6 AN | Pump & Line Kit |
Return Port Size: | 16mm - 8AN | Steering Shaft Kit |
Pump Required: | High Flow / Pressure | Mounting Hardware |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | 8020940 | Click here to view installation instructions |

1996-2004 Chevy S10/ Sonoma Rack & Pinion kit, Black
Product# 8001020-01
Regular price $1,350.00 Save $-1,350.00On this kit we used our own build of manual rack and pinion in a center take-off style rear steer rack. This style of rack and pinion bolts up into place where the existing steering box and idler arm is bolted. This unit is pounds lighter than the original steering and maximizes clearance for V-8 swaps. On a V-8 swap, we successfully used Hedman Shorty style headers. This kit has been used on project cars that use an S-10 frame, but the linkage back up to the column is up to you. This kit is for 2-wheel, rear wheel drive vehicles only.
Note: You will need to reuse or obtain the two factory 5/8"-18 right hand thread outer tie rod ends for this kit.
Tech Info: |
Kit Includes: | |
Pinion Type / Size: | 9/16" - 26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Mounting Bracket |
Turns Lock to Lock: | 4.5 Turns | Steering Shaft Kit |
Pressure Port Size: | NA | Mounting Hardware |
Return Port Size: | NA | |
Pump Required: | NA | |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | Reuse Originals |
Click Here to Look at Product Instructions

1975-81 Firebird/Trans Am Power Rack and Pinion Kit
Product# 8011110-01-01
Regular price $1,820.00 Save $-1,820.00For this Pontiac kit we used a front steer, center take-off style rack and pinion made to match the original center-link of these cars. The rack and pinion match the stock front suspension for great handling, responsiveness, and no bump steer! The rack comes mounted to a one piece bracket which bolts up to the same factory holes on the frame that held the steering box and idler arm.
We did our first install on a 455, and we used Dynomax Headers (Their Part #86104). Other headers may work, but might require modifications.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 3/4"-36 Spline | Rack & Pinion |
Amount of Travel: | 6.75" | Mounting Bracket |
Turns Lock to Lock: | 3 Turns | Pump & Line Kit |
Pressure Port Size: | 18mm - 6 AN Banjo (lower) | Steering Shaft Kit |
Return Port Size: | 16mm - 6 AN Banjo (upper) | Mounting Hardware |
Pump Required: | High Flow / Pressure | |
Inner End Threads: | 11/16"-18 Female | |
Outer ends: | Reuse Originals | Click here to view installation instructions |

1973-87 Chevy C10 Power Rack & Pinion Kit
Product# 8012380-01-01
Regular price $1,840.00 Save $-1,840.00On this kit we used a traditional style rear steer rack & pinion that is mounted to a one piece bracket which bolts up to the outside of either frame rail in the same holes as the original steering box and idler arms.
This kit is for rear wheel drive vehicles only, NOT 4x4s. Installs have been done on V-8s, so there should be room if using a 6 Cylinder. There is quite a bit of room for the shaft support, but some headers may require modification. A two groove pulley on your water pump is required for this kit.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 3/4"-DD | Rack & Pinion |
Amount of Travel: | 5.75" | Mounting Bracket |
Turns Lock to Lock: | 2 7/8 Turns | Pump & Line Kit |
Pressure Port Size: | Straight to #6 AN (upper) | Steering Shaft Kit |
Return Port Size: | Straight to #6 AN (lower) | Mounting Hardware |
Pump Required: | Low Flow | |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | Uses Factory |
Click Here to Look at Product Instructions

1979-93 Ford Mustang Power Standard Ratio, Powder Coated
Product# 8010020
Regular price $449.00 Save $-449.00This kit has everything you need to switch over to a standard ratio power rack & pinion. This kit is rebuilt to be better than new. This kit is also available in a quick ratio 8010080. This power rack and pinion comes with Unisteer's Limited Lifetime Warranty. The rack is a Low Flow unit, that uses port sizes of 5/8" and 9/16".
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 3/4"-36 w/ Milled Flat | Rack & Pinion |
Amount of Travel: | 5.375" | |
Turns Lock to Lock: | 3 Turns | |
Pressure Port Size | 5/8" | |
Return Port Size | 9/16" | |
Pump Required | Low Flow / Pressure | |
Inner End Threads: | 9/16"-18 | |
Mounting Boss | 15.5" |

1994-2004 Ford Mustang Manual Standard Ratio (rack only)
Product# 8000560
Regular price $299.00 Save $-299.00Convert your 1994-2004 FORD MUSTANG from power steering to STANDARD RATIO manual steering! Drop the weight and power drain of a Power Rack & Pinion and Power Steering Pump!

1958-64 Impala/Bel Air Big Block Short Water Rack and Pinion Kit
Product# 8011050-01-01
Regular price $1,850.00 Save $-1,850.00This is a front steer center take off style rack & pinion that matches the stock front end and suspension. The rack is mounted to a one piece mounting bracket that bolts into the same factory holes for the steering box and idler arm. The kit does clear the Z Bar and 4 speed linkage, but does not work with the factory 348 & 409 Engines. If your vehicle had factory power steering, you will need to use our stabilizer bar mounts which are included in place of the factory mounts.
Our kit probably will not work with aftermarket suspension that change the original suspension, but give us a call!
This kit works on most big block engine applications with short water pumps. Installs have been done successfully using Hooker Long Tube Headers. The kits are complete with a shaft kit which includes two u-joints and shafting as well as a pump kit with a pump matched to the gear, clip on reservoir, and Single V-Groove Pulley. Serpentine Pulleys are also available. Pump kits for Long Water Pumps are also available.
Note: Kit can be adapted to fit your needs by selecting the pulley option above.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 3/4" - 36 Spline | Rack & Pinion |
Amount of Travel: | 7" | Outer Tie Rod Ends |
Turns Lock to Lock: | 3 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6 AN | Pump & Line Kit |
Return Port Size: | 16mm - 8AN | Steering Shaft Kit |
Pump Required: | High Flow / Pressure | Mounting Hardware |
Inner End Threads: | M14 x 1.5 | |
Outer ends: | 8020940 | Click here to view installation instructions |

1967-69 Camaro Small Block Short Water Pump Power R&P Super Kit
Product# 8011450-01
Regular price $1,465.00 Save $-1,465.00Unisteer's kits are based off the stock cross-member and steering linkage. The power rack & pinion is a narrowed GM rack. This is machined so that the internal pivot points match the dimensions of the original center link and control arms on the Camaro front end. This gives you the steering you deserve.
The racks come mounted to a simple one piece bracket that mounts up right behind the stock cross member at the rear lower control arm bolts. Simply slide out the original bolts and replace with the supplied longer bolts to install the rack. The power rack & pinion comes with a new set of bolt-on steering arms which mount to the original spindles and ensure you maintain your turning radius.
These kits can be used with either the factory column or an aftermarket column, Choose whether you want a two or three u-joint shaft kit and what column you want to mount the shaft kit to - factory, 1" DD or 1" - 48 tooth spline.
The Power rack kits have been successfully used on cars with small block and big block motors. Headers can present an issue with clearance for the shaft linkage.
Note: Most aftermarket Heads have raised exhaust floors by 1/4" to 1/2" which does not make clearance any easier.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 5" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 Turns | Mounting Bracket |
Pressure Port Size: | Banjo - 6 AN (lower) | Steering Arms |
Return Port Size: | Banjo - 6AN (upper) | Pump and Line Kit |
Pump Required: | Low Flow / Pressure | Steering shaft kit |
Inner End Threads: | M14 x 1.5 | Mounting Hardware |
Outer ends: | 10002 |

Late 1967-70 Mustang Manual Rack & Pinion Kit
Product# 8001090-01-01
Regular price $1,275.00 Save $-1,275.00Our early Mustang Rack Kit greatly improves the steering and handling when compared to that old steering box. This is a center take-off style rack and pinion that utilizes an offset ball center bar which duplicates the stock center link; this means that the rack matches the exact geometry of the original front suspension. Effectively eliminating bump steer, and creating great handling.
The rack comes mounted to a one piece mounting bracket which replaces the tubular cross member located directly behind the front suspension. Since the racks are center take-off style, we off set the rack on the mounting bracket; moving the pinions closer to the driver-side frame which makes connection of the steering linkage to a column as easy as possible.
From a steering standpoint, we found that the early Mustangs split mid 1967 and there were slight differences, so make sure you order the correct kit! Additionally, later model Mustangs and Cougars may look the same, but are NOT - check out our Cougar Rack & Pinion Kits.
The kit will work on Small Block & Big Block cars, and have been successfully used with Stock Manifolds, and Hooker Super Comp Headers. Other Headers may work, but we can't guarantee an easy install. This kit requires the use of a mini starter. This kit may require some modifications on Mustangs with Dart Heads and other Aftermarket Heads requiring different headers.
Note: Granada Spindles have been used on these cars. Please indicate this to us with the drop down menu above, so we can swap the outer ends you will need. Also, If you have a 351C motor you will need to use Headman headers.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 9/16"-26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 4.5 Turns | Mounting Bracket |
Pressure Port Size: | NA | Steering Shaft Kit |
Return Port Size: | NA | Mounting Hardware |
Pump Required: | NA | |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | 8021320 / 8021330 | |
Granada Outer Ends: | 8021250 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

Early 1967 Mustang Power Rack & Pinion Kit for Big Block
Product# 8010910-01-01
Regular price $1,750.00 Save $-1,750.00Our early Mustang Rack Kit greatly improves the steering and handling when compared to that old steering box. This is a center take-off style rack and pinion that utilizes an offset ball center bar which duplicates the stock center link; this means that the rack matches the exact geometry of the original front suspension. Effectively eliminating bump steer, and creating great handling.
The rack comes mounted to a one piece mounting bracket which replaces the tubular cross member located directly behind the front suspension. Since the racks are center take-off style, we off set the rack on the mounting bracket; moving the pinions closer to the driver-side frame which makes connection of the steering linkage to a column as easy as possible.
From a steering standpoint, we found that the early Mustangs split mid 1967 and there were slight differences, so make sure you order the correct kit! Additionally, later model Mustangs and Cougars may look the same, but are NOT - check out our Cougar Rack & Pinion Kits.
The kit will work on Big Block cars, and have been successfully used with Stock Manifolds, and Hooker Super Comp Headers. Other Headers may work, but we can't guarantee an easy install. This kit requires the use of a mini starter. This kit may require some modifications on Mustangs with Dart Heads and other Aftermarket Heads requiring different headers.
Note: Granada Spindles have been used on these cars. Please indicate this to us with the drop down menu above, so we can swap the outer ends you will need.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 6" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 - 2.75 Turns | Mounting Bracket |
Pressure Port Size: | 18mm - 6AN | Pump & Line Kit |
Return Port Size: | 16mm - 6AN | Steering Shaft Kit |
Pump Required: | Low Flow 1100 psi | Mounting Hardware |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | 8021320 / 8021330 | |
Granada Outer Ends | 8021250 | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1967-69 Camaro Small Block Long Water Pump Power R&P Super Kit
Product# 8011490-01
Regular price $1,505.00 Save $-1,505.00Unisteer's kits are based off the stock cross-member and steering linkage. The power rack & pinion is a narrowed GM rack. This is machined so that the internal pivot points match the dimensions of the original center link and control arms on the Camaro front end. This gives you the steering you deserve.
The racks come mounted to a simple one piece bracket that mounts up right behind the stock cross member at the rear lower control arm bolts. Simply slide out the original bolts and replace with the supplied longer bolts to install the rack. The power rack & pinion comes with a new set of bolt-on steering arms which mount to the original spindles and ensure you maintain your turning radius.
These kits can be used with either the factory column or an aftermarket column, Choose whether you want a two or three u-joint shaft kit and what column you want to mount the shaft kit to - factory, 1" DD or 1" - 48 tooth spline.
The Power rack kits have been successfully used on cars with small block and big block motors. Headers can present an issue with clearance for the shaft linkage.
Note: Most aftermarket Heads have raised exhaust floors by 1/4" to 1/2" which does not make clearance any easier.
Tech Info: | Kit Includes: | |
Pinion Type / Size: | 17mm DD | Rack & Pinion |
Amount of Travel: | 5" | Outer Tie Rod Ends |
Turns Lock to Lock: | 2.5 Turns | Mounting Bracket |
Pressure Port Size: | Banjo - 6 AN (lower) | Steering Arms |
Return Port Size: | Banjo - 6AN (upper) | Pump and Line Kit |
Pump Required: | Low Flow / Pressure | Steering shaft kit |
Inner End Threads: | M14 x 1.5 | Mounting Hardware |
Outer ends: | 10002 |

1928-32 Ford Cross Steer® New Build Kit (no shaft kit) Black Bracket
Product# 8000460-01
Regular price $450.00 Save $-450.00The Cross Steer is essentially a small half rack and pinion that bolts into place exactly where the Vega style steering box would bolt on. The system still uses a draglink between both wheels. The Cross Steer was specifically designed for solid axle cars and trucks of this era with a mono leaf spring suspension. Since the Cross Steer pivots only off the one side, it matches up perfectly with the stock suspension of the solid axle Fords. Sorry, it will not work on Chevys which had dual leaf springs.
Note: You must have split wishbones (at least 12 inches) or hairpins for the Cross Steer to properly work.
The gear comes mounted to an angled bracket that has the same three hole pattern for mounting the Vega box. This small rack & pinion is made of all automotive grade components and can handle a vehicle up to 3500 lbs!
If you are building a new vehicle, the regular Cross Steer is the best option and you can run your steering linkage down to the gear. We can even send you a Cross Steer with a plain steel bracket that you could weld to your frame and paint to match. If you still have a Vega Box, check out our retrofit that has a shaft kit. This shaft kit consists of a coupler and a shaft with a splined end which is the same size as the Vega spline so you can reuse your existing steering linkage. The switch over can be done in only an hour or two!
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 9/16"-26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Mounting Bracket |
Turns Lock to Lock: | 3.75 Turns | Mounting Hardware |
Pressure Port Size: | NA | |
Return Port Size: | NA | |
Pump Required: | NA | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |
Inner End Threads: | Tube & Adapter 11/16"-18 | Click here for IDIDIT Columns for your Streetrod! |

1982-95 Chevy S10/ Sonoma Rack only, Black
Product# 8000980-01
Regular price $925.00 Save $-925.00On this kit we used our own build of manual rack and pinion in a center take-off style rear steer rack. This style of rack and pinion bolts up into place where the existing steering box and idler arm is bolted. This unit is pounds lighter than the original steering and maximizes clearance for V-8 swaps. On a V-8 swap, we successfully used Hedman Shorty style headers. This kit has been used on project cars that use an S-10 frame, but the linkage back up to the column is up to you. This kit is for 2-wheel, rear wheel drive vehicles only.
Note: You will need to reuse or obtain the two factory 5/8"-18 right hand thread outer tie rod ends for this kit.
Tech Info: |
Kit Includes: |
Pinion Type / Size: | 9/16" - 26 Spline | Rack & Pinion |
Amount of Travel: | 6" | Mounting Bracket |
Turns Lock to Lock: | 4.5 Turns | Mounting Hardware |
Pressure Port Size: | NA | |
Return Port Size: | NA | |
Pump Required: | NA | |
Inner End Threads: | 9/16" - 18 | |
Outer ends: | Reuse Originals | CLICK HERE TO LOOK AT PRODUCT INSTRUCTIONS |

1928-32 Ford Cross Steer® New Build (No Shaft Kit) w/ Mounting Holes (Paintable Steel Bracket)
Product# 8000460-03
Regular price $450.00 Save $-450.00The Cross Steer is essentially a small half rack and pinion that bolts into place exactly where the Vega style steering box would bolt on. The system still uses a draglink between both wheels. The Cross Steer was specifically designed for solid axle cars and trucks of this era with a mono leaf spring suspension. Since the Cross Steer pivots only off the one side, it matches up perfectly with the stock suspension of the solid axle Fords. Sorry, it will not work on Chevys which had dual leaf springs.
Note: You must have split wishbones (at least 12 inches) or hairpins for the Cross Steer to properly work.
The gear comes mounted to an angled bracket that has the same three hole pattern for mounting the Vega box. This small rack & pinion is made of all automotive grade components and can handle a vehicle up to 3500 lbs!
If you are building a new vehicle, the regular Cross Steer is the best option and you can run your steering linkage down to the gear. We can even send you a Cross Steer with a plain steel bracket that you could weld to your frame and paint to match. If you still have a Vega Box, check out our retrofit that has a shaft kit. This shaft kit consists of a coupler and a shaft with a splined end which is the same size as the Vega spline so you can reuse your existing steering linkage. The switch over can be done in only an hour or two!